Thermal Management
The SinkPAD-II SP-05-A8 module requires careful attention to mounting and cooling to ensure that the junction temperature of the LED is kept well below the maximum rating specified in the Lumileds datasheet.
We recommend that the module be mounted to an aluminum or copper finned heatsink exposed to open air for optimal cooling. The module can be mounted to the heat sink in one of two ways:
- 10mm square pressure sensitive, thermally conductive tape (Recommended)
- Arctic Silver thermally conductive adhesive
Before fastening the module to the heat sink, ensure that the two mating surfaces are perfectly flat and clean to maximize heat transfer to the heatsink. Mechanical fasteners are not recommended for this module.
The bottom of the LED module is electrically neutral, so it is unnecessary to electrically isolate the base from the cooling surface.
Stock
We usually keep a small number of this part in stock. However, we can produce virtually any quantity you require on demand. Please get in touch with us for lead times for orders above 1,000 pieces.
LED Binning
Order quantities less than 1,000 pieces are produced from unbinned stock (cut strips). We can supply binned LED modules (built from full reels)) If you order in 1,000+ quantities, please contact us for binning details.
You can learn more about LED binning here.
LED Color | Amber |
Recommended Operating Current | 350 mA |
Maximum Rated Drive Current | 700 mA |
Maximum Pulse Current | 700 mA |
Typical Forward Voltage | 2.1 Vf |
Maximum Forward Voltage | 2.6 Vf |
Lumens @ 350 mA | 74 lm |
Lumens @ 700 mA | 137 lm |
Wavelength Range | 585 to 595 K |
Beam Angle | 125° |
Thermal Resistance | 7.7 °C/W |
Maximum Recommended Junction Temp | 135 °C |
Operating Temperature Range | -40 to 135 °C |
Dimensions (L x W x H) | 10 x 10 x 3.7 mm |
Weight | 0.3 g |
Refer to the product datasheets for complete specifications. |
---|
A current-regulating LED driver is required between the power supply and the LED module to ensure that the LED is not powered above its maximum current rating. You can learn more about powering high-power LED modules here.
All drivers listed here are 100% compatible with the SP-05-A8 LED module. The driver you select will depend on your specific requirements.
Product Information | Stock | Price | hf:att:pa_output-current | hf:att:pa_connection | hf:att:pa_dimming |
---|
High-power LEDs include a primary optic for protection and light optimization. However, a secondary optic is often essential for better focus and light distribution.
All the optics except the Polymer 15 mm optic are 100% compatible with the SP-05-A8 LED module. Polymer 15 mm optics cannot be used if you select the connector option.
Note: The optics listed here may not be ideal for ultraviolet or infrared LEDs. You will need to test the optic for your specific application.
Product Information | Stock | Price | hf:att:pa_beam-type | hf:att:pa_mounting |
---|
To maximize life and reliability, a heatsink or alternate method of cooling is required to ensure that the junction temperature of the LED is kept well below its maximum temperature rating.
Refer to our Thermal Management articles for assistance selecting an appropriate heatsink from the available options here.
Product Information | Stock | Price | hf:att:pa_length-hs | hf:att:pa_width-hs | hf:att:pa_height-hs | hf:att:pa_cw-filter | hf:att:pa_fin-type |
---|
RoHS Status | RoHS 3 Compliant |
REACH Status | REACH Uneffected |
Conflict Minerals Report | CMRT Rev 6.22 |
Proposition 65 Statement | Proposition 65 |
PFAS Declaration | PFAS Declaration |
ECCN | EAR99 |
HTS | 8543.70.71.00 |
Country of Origin | CA |
Thermal Management
The SinkPAD-II SP-05-A8 module requires careful attention to mounting and cooling to ensure that the junction temperature of the LED is kept well below the maximum rating specified in the Lumileds datasheet.
We recommend that the module be mounted to an aluminum or copper finned heatsink exposed to open air for optimal cooling. The module can be mounted to the heat sink in one of two ways:
- 10mm square pressure sensitive, thermally conductive tape (Recommended)
- Arctic Silver thermally conductive adhesive
Before fastening the module to the heat sink, ensure that the two mating surfaces are perfectly flat and clean to maximize heat transfer to the heatsink. Mechanical fasteners are not recommended for this module.
The bottom of the LED module is electrically neutral, so it is unnecessary to electrically isolate the base from the cooling surface.
Stock
We usually keep a small number of this part in stock. However, we can produce virtually any quantity you require on demand. Please get in touch with us for lead times for orders above 1,000 pieces.
LED Binning
Order quantities less than 1,000 pieces are produced from unbinned stock (cut strips). We can supply binned LED modules (built from full reels)) If you order in 1,000+ quantities, please contact us for binning details.
You can learn more about LED binning here.
LED Color | Amber |
Recommended Operating Current | 350 mA |
Maximum Rated Drive Current | 700 mA |
Maximum Pulse Current | 700 mA |
Typical Forward Voltage | 2.1 Vf |
Maximum Forward Voltage | 2.6 Vf |
Lumens @ 350 mA | 74 lm |
Lumens @ 700 mA | 137 lm |
Wavelength Range | 585 to 595 K |
Beam Angle | 125° |
Thermal Resistance | 7.7 °C/W |
Maximum Recommended Junction Temp | 135 °C |
Operating Temperature Range | -40 to 135 °C |
Dimensions (L x W x H) | 10 x 10 x 3.7 mm |
Weight | 0.3 g |
Refer to the product datasheets for complete specifications. |
---|
A current-regulating LED driver is required between the power supply and the LED module to ensure that the LED is not powered above its maximum current rating. You can learn more about powering high-power LED modules here.
All drivers listed here are 100% compatible with the SP-05-A8 LED module. The driver you select will depend on your specific requirements.
Product Information | Stock | Price | hf:att:pa_output-current | hf:att:pa_connection | hf:att:pa_dimming |
---|
High-power LEDs include a primary optic for protection and light optimization. However, a secondary optic is often essential for better focus and light distribution.
All the optics listed here are 100% compatible with the SP-05-A8 LED module.
Product Information | Stock | Price | hf:att:pa_beam-type | hf:att:pa_mounting |
---|
To maximize life and reliability, a heatsink or alternate method of cooling is required to ensure that the junction temperature of the LED is kept well below its maximum temperature rating.
Refer to our Thermal Management articles for assistance selecting an appropriate heatsink from the available options here.
Product Information | Stock | Price | hf:att:pa_length-hs | hf:att:pa_width-hs | hf:att:pa_height-hs | hf:att:pa_cw-filter | hf:att:pa_fin-type |
---|
RoHS Status | RoHS 3 Compliant |
REACH Status | REACH Uneffected |
Conflict Minerals Report | CMRT Rev 6.22 |
Proposition 65 Statement | Proposition 65 |
PFAS Declaration | PFAS Declaration |
ECCN | EAR99 |
HTS | 8543.70.71.00 |
Country of Origin | CA |