395nm LUXEON Z Ultraviolet on a Saber Z1 10mm Square Base – 675 mW @ 500mA
| Product Attributes | |
|---|---|
| LED Color | Ultraviolet |
| (1)Radiometric Power @ 500mA | 675 mW |
| (2)Peak Wavelength | 395nm |
| (3)Beam Angle | 140° |
| (4)Recommended Operating Current | 500 mA |
| Maximum Rated Drive Current | 1000 mA |
| (5)Minimum Forward Voltage | 2.9 Vf |
| (5,7)Maximum Forward Voltage | 3.4 Vf |
| (2)Thermal Resistance | 5.5 C°/W |
| Max Recommended Junction Temp | 120 °C |
| Operating Temperature Range | -40 to 120 °C |
| Dimensions L x W x H | 10 x 10 x 2.3 mm |
|
|
| Documents & Media | |
|---|---|
| Datasheets | SZ-01 Module Datasheet LHUV-0395-A065 LUXEON Z LED Datasheet |
| CAD & Drawings | SZ-01 Module Dimensional Drawing |
Thermal Management
The Saber Z1 module requires careful attention to mounting and cooling to ensure that the junction temperature of the LED is kept well below the maximum rating as specified in the LED documentation published by Lumileds.
For optimal cooling, we recommend that the module be mounted to a suitable finned heat sink (aluminum or copper) that is exposed to open air. The module can be mounted to the heat sink in one of two ways:
- 10mm square pressure sensitive, thermally conductive tape (Recommended)
- Arctic Silver thermally conductive adhesive
Before fastening the module to the heat sink, ensure that the two mating surfaces are perfectly flat and clean in order to maximize heat transfer to the the sink. This module is not designed to be fastened with screws.
The bottom of the LED module is electrically neutral, so it is not necessary to electrically isolate the base from the cooling surface.
Optic Compatibility
The Saber Z1 has been specifically designed to accommodate all 10mm square Carclo optics. You will find a complete list of 100% compatible optics here.
We currently do not carry these optics, however the Saber Z1 is also compatible with:
- Ledil – Larisa & Lisa series
- Khatod – PL1670 & PL1699 series
Additional Information
If you order more than one piece of this part, pieces may be shipped as part of a routed panel that is v-scored so that each carrier tab can be separated from the panel.
Do you need LEDs with a specific flux, color or forward voltage? Order this part in 1,000 piece increments and we will build it using LEDs from the same bin. We can also provide specific bin numbers. Contact us for availability.
Click here to learn more about LED binning.
Discount Pricing
Email when stock available
| Quantity | Discount |
|---|---|
| 10-24 | 5% |
| 25-49 | 10% |
| 50+ | 15% |
Email when stock available
Discount Pricing
| Quantity | Discount |
|---|---|
| 10-24 | 5% |
| 25-49 | 10% |
| 50+ | 15% |
Thermal Management
The SZ-01-U6 Saber Z1 LED module requires careful attention to mounting and cooling to ensure that the junction temperature of the LED is kept well below the maximum rating specified in the Lumileds datasheet. We recommend that the module be mounted to an aluminum or copper finned heatsink exposed to open air for optimal cooling. The module can be mounted to the heat sink in one of two ways:
- 10mm square pressure-sensitive, thermally conductive tape (Recommended)
- Arctic Silver thermally conductive adhesive
Before fastening the module to the heat sink, ensure that the two mating surfaces are perfectly flat and clean to maximize heat transfer to the heatsink. Mechanical fasteners are not recommended for this module. The bottom of the LED module is electrically neutral, so it is unnecessary to electrically isolate the base from the cooling surface.
Optic Compatibility
The Saber Z5 has been specifically designed to accommodate any Carclo 20mm optic that can be mounted into the Carclo 20mm Pegged Foot Optic Holder. We currently do not carry these optics; however, the Saber Z5 is also compatible with:
- Ledil – Larisa & Lisa series
- Khatod – PL1670 & PL1699 series
Carrier Tab
The Saber Z1 is provided as part of a Carrier Tab. The tab is v-scored so that the LED module can be easily separated from the carrier. The carrier tab makes it easier to handle the Saber Z1 during transport, storage, and module, minimizing the risk of damage to the LED emitting surface.
Stock
We usually keep a small number of this part in stock. However, we can produce virtually any quantity you require on demand. Please get in touch with us for lead times for orders above 1,000 pieces.
LED Binning
Order quantities less than 2,000 pieces are produced from unbinned stock (cut strips). We can supply binned LED modules (built from full reels)) If you order in 2,000+ quantities, please contact us for binning details. You can learn more about LED binning here.
| LED Color | Ultraviolet |
| Radiometric Power @ 500 mW | 675 mW |
| Peak Wavelength | 395 nm |
| Recommended Operating Current | 500 mA |
| Maximum Rated Drive Current | 1000 mA |
| Maximum Pulse Current | 1300 mA |
| Typical Forward Voltage | 3.15 Vf |
| Maximum Forward Voltage | 3.4 Vf |
| Wavelength Range | 390 to 400 K |
| Beam Angle | 140° |
| Thermal Resistance | 5.5 °C/W |
| Maximum Recommended Junction Temp | 120 °C |
| Operating Temperature Range | -40 to 135 °C |
| Dimensions (L x W x H) | 10 x 10 x 2.3 mm |
| Weight | 0.9 g |
| Refer to the product datasheets for complete specifications. | |
|---|---|
A current-regulating LED driver is required between the power supply and the LED module to ensure the LED is not driven beyond its maximum current rating. You can learn more about powering high-power LED modules here.
All drivers listed here are 100% compatible with the SZ-01-U6 LED module. The driver you select will depend on your specific requirements.
| Product Information | Stock | Price | hf:att:pa_output-current | hf:att:pa_connection | hf:att:pa_dimming |
|---|
High-power LEDs include a primary optic for protection and light optimization. However, a secondary optic is often essential for better focus and light distribution.
All the optics except the Polymer 15 mm optic are 100% compatible with the SZ-01-U6 LED module. Polymer 15 mm optics cannot be used if you select the connector option.
Note: The optics listed here may not be ideal for ultraviolet or infrared LEDs. You will need to test the optic for your specific application.
| Product Information | Stock | Price | hf:att:pa_beam-type | hf:att:pa_mounting |
|---|
To maximize life and reliability, a heatsink or an alternative cooling method is required to keep the LED junction temperature well below its maximum rating.
Refer to our Thermal Management articles for assistance in selecting an appropriate heatsink from the available options here.
| Product Information | Stock | Price | hf:att:pa_length-hs | hf:att:pa_width-hs | hf:att:pa_height-hs | hf:att:pa_cw-filter | hf:att:pa_fin-type |
|---|
| RoHS Status | RoHS 3 Compliant |
| REACH Status | REACH Uneffected |
| Conflict Minerals Report | CMRT Rev 6.22 |
| Proposition 65 Statement | Proposition 65 |
| PFAS Declaration | PFAS Declaration |
| ECCN | EAR99 |
| HTS | 8539.51.00.00 |
| Country of Origin | CA |
Thermal Management
The SZ-01-U6 Saber Z1 LED module requires careful attention to mounting and cooling to ensure that the junction temperature of the LED is kept well below the maximum rating specified in the Lumileds datasheet. We recommend that the module be mounted to an aluminum or copper finned heatsink exposed to open air for optimal cooling. The module can be mounted to the heat sink in one of two ways:
- 10mm square pressure-sensitive, thermally conductive tape (Recommended)
- Arctic Silver thermally conductive adhesive
Before fastening the module to the heat sink, ensure that the two mating surfaces are perfectly flat and clean to maximize heat transfer to the heatsink. Mechanical fasteners are not recommended for this module. The bottom of the LED module is electrically neutral, so it is unnecessary to electrically isolate the base from the cooling surface.
Optic Compatibility
The Saber Z5 has been specifically designed to accommodate any Carclo 20mm optic that can be mounted into the Carclo 20mm Pegged Foot Optic Holder. We currently do not carry these optics; however, the Saber Z5 is also compatible with:
- Ledil – Larisa & Lisa series
- Khatod – PL1670 & PL1699 series
Carrier Tab
The Saber Z1 is provided as part of a Carrier Tab. The tab is v-scored so that the LED module can be easily separated from the carrier. The carrier tab makes it easier to handle the Saber Z1 during transport, storage, and module, minimizing the risk of damage to the LED emitting surface.
Stock
We usually keep a small number of this part in stock. However, we can produce virtually any quantity you require on demand. Please get in touch with us for lead times for orders above 1,000 pieces.
LED Binning
Order quantities less than 2,000 pieces are produced from unbinned stock (cut strips). We can supply binned LED modules (built from full reels)) If you order in 2,000+ quantities, please contact us for binning details. You can learn more about LED binning here.
| LED Color | Ultraviolet |
| Radiometric Power @ 500 mW | 675 mW |
| Peak Wavelength | 395 nm |
| Recommended Operating Current | 500 mA |
| Maximum Rated Drive Current | 1000 mA |
| Maximum Pulse Current | 1300 mA |
| Typical Forward Voltage | 3.15 Vf |
| Maximum Forward Voltage | 3.4 Vf |
| Wavelength Range | 390 to 400 K |
| Beam Angle | 140° |
| Thermal Resistance | 5.5 °C/W |
| Maximum Recommended Junction Temp | 120 °C |
| Operating Temperature Range | -40 to 135 °C |
| Dimensions (L x W x H) | 10 x 10 x 2.3 mm |
| Weight | 0.9 g |
| Refer to the product datasheets for complete specifications. | |
|---|---|
A current-regulating LED driver is required between the power supply and the LED module to ensure that the LED is not powered above its maximum current rating. You can learn more about powering high-power LED modules here.
All drivers listed here are 100% compatible with the SZ-01-U6 LED module. The driver you select will depend on your specific requirements.
| Product Information | Stock | Price | hf:att:pa_output-current | hf:att:pa_connection | hf:att:pa_dimming |
|---|
High-power LEDs include a primary optic for protection and light optimization. However, a secondary optic is often essential for better focus and light distribution.
All the optics listed here are 100% compatible with the SZ-01-U6 LED module.
| Product Information | Stock | Price | hf:att:pa_beam-type | hf:att:pa_mounting |
|---|
To maximize life and reliability, a heatsink or alternate method of cooling is required to ensure that the junction temperature of the LED is kept well below its maximum temperature rating.
Refer to our Thermal Management articles for assistance selecting an appropriate heatsink from the available options here.
| Product Information | Stock | Price | hf:att:pa_length-hs | hf:att:pa_width-hs | hf:att:pa_height-hs | hf:att:pa_cw-filter | hf:att:pa_fin-type |
|---|
| RoHS Status | RoHS 3 Compliant |
| REACH Status | REACH Uneffected |
| Conflict Minerals Report | CMRT Rev 6.22 |
| Proposition 65 Statement | Proposition 65 |
| PFAS Declaration | PFAS Declaration |
| ECCN | EAR99 |
| HTS | 8539.51.00.00 |
| Country of Origin | CA |
